1. SHOWER DOORS
2, "HOW TO"  INSTALL
3. TESTIMONIALS
4. DOOR DRAWINGS
5. GALLERY
6. LOCATIONS
7. FINISHES
8. HINGES
9. HANDLES
10. CLAMPS
11. HEADERS
12. U-CHANNEL
13. VINYL SEALS
14. SUPPORT BARS
15. SLIDNG DOORS
16. HYDROSLIDE
17. BI-FOLD DOORS
18. STAINLESS SLIDING
        SHOWER DOOR
19. GLASS TILES
20. STAINLESS         ROLLING HRDW
21. CONTOUR ROLLER
22. DIRECT ROLLERS
23. MORTISE
24. DOUBLE MORTISE
25. STRAP ROLLERS
26. DOUBLE STRAP
27. ROUND BAR
28. POLISHED
29. PARTS
 
30. ALUMINUM
      SLIDING DOORS
31. EPCO
32. CONTRACTORS
WARDROBE
33. COTTAGE
34. HYDROSLIDE
35. GLASS TILES
 
36. GLASS INFO
37. STRENGTH
38. FLAT GLASS
39. BENT GLASS
40. ART GLASS
41. LAMINATED
42. CABINET GLASS
43. COATINGS
 
44. RAILINGS
45. Z-BRACKETS
46. MINI - Z-BRACKETS
47. RSOB BRACKETS
48. STANDOFFS
49. BASE SHOE
50. SS POSTS
51. ALUMINUM
52. CAP RAILS
 
53. STANDOFFS
54.  2" DIA.
55.  1 1/2" DIA
56. 1 1/4" DIA.
57. - 1" DIA.
58. - 3/4" DIA.
59. - 1/2" DIA.
60. SLOTTED
61. MINI SLOTTED
62. - 1 1/4" SQUARE
63. 3/4" SQUARE
64. POLE ADAPT.
 
65. STORE FRONTS
 
66. REPAIR PARTS
          FOR OLDER
          SHOWERS
67. GLASS CLEANER
68. SHELVES AND
          BRACKETS
69. SEALANT

70. TOOLS
71. DISPLAY HARDWARE
72. CABINET HINGES
73. CABINET LOCKS
 
74. F.A.Q.
75. CONTACT
76. LINKS
77. CHARTS
78. CHECKOUT
79. SEARCH

Support Bars

The standard Support Bar (SUP10), comes in two versions: Wall to Glass, and Glass to Glass.
Top picture on the right is Wall to Glass mount. Below that is Glass to Glass mount. The pole section is 39" long (One meter.) Many finishes.

There are other end pieces shown below. You can buy the poles and end pieces separately to make many configurations. The poles come in two sizes, 39" and 51", but we can have custom sizes fabricated.
The poles are tubular brass with a high quality finish to match the rest of your hardware.


39" Wall Mount Support Bar - SUP10
Door is on the far left. Support Bar keeps the side panel lined up and rigid. Note the Victorian handle and Sleeve over glass clamps at the top corners. Good luck finding those on our web site.
Glass to Glass Support Bar SUP20: Can be used at the top of a NEO Angle instead of a regular header. This gives you more of a European Look: tan and young, everyone you pass will go, "Ahhh."

39" long bar - S1

51" Long Bar - S2

To build your own support bar, you can buy the ends and poles separately.

Standard Wall Mount Bracket - S3

Standard Glass Clamp End for 3/8 and 1/2" Glass - S5

Glass Clamp End for 1/4" Glass - S4

SBB45
 Allows for angled brackets as in the drawing.
The other end would be the S5.
SUP135 -Through Glass Support Bar is another choice for diagonal support. This part comes with 39" bar to make 42 5/8" over all maximum length. Requires a hole in the glass. Glass to Glass Mount and Wall to Glass Mount.
S7
This bracket can be used with the tubular bar (S1 or S2) as a header such as SDH980, to span the panel and the door when you have a glass to glass hinge.
S910
We've used this bracket to fasten the edge of a panel to the ceiling. The building inspector said that the code required the glass to be fastened on all sides. So we ran the support bar to the ceiling which did not add any strength, but it satisfied the inspector. The code is ambiguous and I've heard that it will be changed when the new code book comes out.

S13
This bracket is used when the support bar has to be the same height as the top edge of the panel. This might happen when you are near an airport and are worried about low flying aircraft.

 

90° Corner - S8
Corner Bracket for making stylish header for corner shower with glass to glass hinges.

 
S12
Slim line Wall Mount Bracket.
Alternative to S3
 
     
We accept credit cards, and
Wilson Glass toll free: 866-370-0006 Hours: M-F: 8 to 4:30 and Sat: By appointment only
Read our Privacy and Return Policy