The Contour Roller is probably our best looking roller. It's attributes include the possibility of not using the standoffs, which would place the body of the roller flat against the door. this would make it easier to clean, and give it a simpler look. The Contour Roller has no visible fasteners on the outside.
Below we are offering a variety of kits which include everything you will need but the glass or wood door.

The Safety Pin is removable with a 3 mm Allan Wrench. The hole left by the removed safety pin will always face the wall.This means and of the tracks and hangers can be used.
What is a Safety Pin
Solutions for sheet rock walls. Click Here.

Safety Pin Pros and Cons:
WITH PIN: The Door with safety pin can't be lifted or knocked off the track. This is good for glass doors that are narrower than three feet or whose height is more than twice the width. Also good if you have a locked cabinet of top secrets. Track for the safety pin is pre-drilled and so there is no chance the hangers will line up with your studs. Blocking behind sheet rock is needed. It's difficult to cut the track to size and keep the holes symmetric but it really is fine if the track is a little longer than twice your door width..
NO PIN: The un-drilled track for use without safety pin uses hangers that can be positioned anywhere on the wall. So you can easily hit the studs. We cut the track to size for you and glue on end caps for the track.

The Contour Roller is only $139 each. On this page we are selling complete kits. See drop down box at the bottom of the page. Please call to order individual parts.

Chart of Options and Capacity: Let's say the term, CAPACITY is the distance from the wall to the outside of the door SO if the capacity is 1" and you have 1/2" glass then there will be 1/2" from wall to inside of the glass.
GD-03A Hangers with safety pin and drilled track and with the standoffs = 1"
GD-03A Hangers WITHOUT the standoffs = 1 5/8"
GD-02A Hangers with safety pin and drilled track - WITH standoffs = 1 3/8"
GD-02A Hangers WITHOUT standoffs = 2"
LS102 Hangers Without Safety Pin WITH Standoffs = 15/16"
LS102 Hangers WITHOUT Standoffs = 1 9/16"
(Note: GD-01 Hanger will not work with this roller.)

A large clear plastic gasket is included for use without the standoffs - between glass and metal.
Solutions for sheet rock walls. Click Here.

What is Included:
2 - Contour Rollers with removable standoffs and clear plastic washers.
2 - Culindrical Stops
4 - Hangers with 5' and 6' tracks, 5 hangers with 7' and 8' tracks
Either Glass Bottom Guide or Wood Door Bottom guide.
Track is either drilled or undrilled and it comes in 5' through 8' lengths.
9' and 10' drilled track is available by phone. Undrilled track is in stock up to 20'.
Longer tracks must be shipped by truck.

More Photos: Photo from Inside , Photo 2

Ordering Instructions: 1. The track is typically twice as long as the door. The door overlaps the opening by 1" on each side (2" is fine too.) 2. If you have blocking behind sheetrock, then order drilled track. We don't recommend cutting the drilled track because the holes will not be symetric. But sometmes we can cut it perfectly. Call for that information. Undrilled track can be cut to whatever length you want. Solutions for sheet rock walls. Click Here. 3. Choose the bottom Guide for your door. Wood Bottom guide is cheaper than the glass one. 4. Hangers Choices: If you are ordering drilled track see chart above. If you are ordering undrilled track then we will ship LS102 for Undrilled track. That's the only hanger that will work.

Other Glass Door Systems: Bi-Fold (new) - Strap - Double Strap - Direct Rollers. - Round Bar
Other Wood Door Systems: Strap for Wood - Mortise Rolers - Double Mortise - Double Strap